DIGITAL DASHBOARD " EVO2 "
blue-red leds version cod. EVO2_B red leds version cod. EVO2_R
The "EVO2"dasboard is the Top of Aviacompositi production
In the "EVO2" dashboards there are integrated the main road functions: speedometer, odometer, trip, engine rpm, cooling liquid temperature gauge , main warning lights (where applicable the fuel injection warning light too) and track functions: stopwatch computer that allow the display and memorization of the lap times.
The "EVO2" can store 100 times and visualizes it directly on the display the by means of the selecting buttons placed on right-top side.
TECHNICAL FEATURES
Road Funtions
· Speedometer max speed reaching over 350 Km/h (continuous operation in Mph too presettable by menù; for USA, UK etc. we ship it presetted)
· Odometer 0 to 99999 Km (or Miles presettables as above) it's simply possible load the distance covered by means with previous dashboard
· Trip da 0 a 999.9 resettable (Miles too)
· Speedometer and odometer presetted for 17 inches wheel but easy calibrable for other wheels
· High brightness rev.counter leds, it is visible in the sun light and there is an attenuator for night operation, remote internal illumination
· Languages Italian or English
· Kit inclusive of wiring, speed and temperature sensors
(most wirings has plug compatibles with the means socket)
· Clear operating instructions and easy set up operations
(factory presetted for requested means)
· Rev. counter scales: Road use 1-16000 rpm, 1-15000, 1-14000, 1-12000, 1-10000, 1- 8000 Track use: 5-16000, 3-15000, 3-13000
· 2 years warranty
Track functions
· "Chrono" function 1/100 sec
· 100 laps storing, holds for undefined time without alimentation too, total lap time, best lap, "full-memory" warning,
max reached engine temperature , visualization on the display by means of selection buttons
· Counting and storing of distance covered to show when it pass on the road display
· Shift-light programmable from 5.000 rpm to 15.750 rpm, 250 rpm steps
Accessories
· Automatic infrared lap time operation
· Serial interface (RS232) with software for lap's download on PC
cod.
· Transponder - transmitter TX_IR
· Transponder - receiver RX_U
· PC serial interface RS232
Dimentions
wide 137mm, height 65 mm, depth 55 mm, weight 300 gr. approx.
Other infos
The speed reaching system it's by a sensor usually placed on the front wheel with a special mount included in the kit (this cunning permit to disregard the transmission ratio of the bike or the car because it's count is based on the wheel circumference only) however, it's possible place it on the rear wheel. The "EVO2" cames calibrated for the 17 inches wheel but it can be easily calibrate for other wheels (inserting another value of the wheel circumference), it is possible to set up the distance stored on the old dashboard simply using the setting menu. All the functions can be easily performed by means of the three buttons placed on the right-top side of the dashboard.
The backlight display can visualize the road functions or the track functions, you can switch from one to the other and you can choose the display priority of one of it for the "switch-on" operation.
On both the display modes it visualize the engine temperature too.
When the “Chrono” function runs it show the actual lap counting, the last lap (show in big characters) and the total time of the session. The stored lap-times (till 100) can be visualized on the proper display page accessible by the menu button. It is possible to download the times on a PC by means of a serial RS232 interface.
The start-stop "Chrono" function can be performed manually (by means of a button to fit on the left handle-bar of the bike - so shipped) or automatically by a transponder interface kit to buy separately (see the web page). Besides there is a programmable "shift-light” which is setting by display.
The "EVO2" it's already installed on most of the more diffused bikes and cars.